An audiometry exam tests your ability to hear sounds. Sounds vary based on their loudness (intensity) and the speed of sound wave vibrations (tone).
Hearing occurs when sound waves stimulate the nerves of the inner ear. The sound then travels along nerve pathways to the brain.
Sound waves can travel to the inner ear through the ear canal, eardrum, and bones of the middle ear (air conduction). They can also pass through the bones around and behind the ear (bone conduction).
The INTENSITY of sound is measured in decibels (dB):
- A whisper is about 20 dB
- Loud music (some concerts) is around 80 - 120 dB
- A jet engine is about 140 - 180 dB
Sounds greater than 85 dB can cause hearing loss after a few hours. Louder sounds can cause immediate pain, and hearing loss can develop in a very short time.
The TONE of sound is measured in cycles per second (cps) or Hertz:
- Low bass tones range around 50 - 60 Hz
- Shrill, high-pitched tones range around 10,000 Hz or higher
The normal range of human hearing is about 20 Hz - 20,000 Hz. Some animals can hear up to 50,000 Hz. Human speech is usually 500 - 3,000 Hz.
Audiometry; Hearing test; Audiography (audiogram)
How the Test is Performed
The first steps are to see whether you need an audiogram. The procedure most often involves blocking one ear at a time and checking your ability to hear whispers, spoken words, or the sound of a ticking watch.
A tuning fork may be used. The tuning fork is tapped and held in the air on each side of the head to test the ability to hear by air conduction. It is tapped and placed against the mastoid bone behind each ear to test bone conduction.
Audiometry provides a more precise measurement of hearing. For this test, you wear earphones attached to the audiometer. Pure tones of controlled intensity are delivered to one ear at a time. You are will be asked to raise a hand, press a button, or otherwise indicate when you hear a sound.
The minimum intensity (volume) required to hear each tone is graphed. A device called a bone oscillator is placed against the bone behind each ear (mastoid bone) to test bone conduction.
How to Prepare for the Test
No special steps are needed.
How the Test will Feel
There is no discomfort. The length of time varies. An initial screening may take about 5 to 10 minutes. Detailed audiometry may take about 1 hour.
Why the Test is Performed
This test can detect hearing loss at an early stage. It may also be used when you have hearing problems from any cause.
Common causes of hearing loss include:
The ability to hear a whisper, normal speech, and a ticking watch is normal.
The ability to hear a tuning fork through air and bone is normal.
In detailed audiometry, hearing is normal if you can hear tones from 250 Hz - 8,000 Hz at 25 dB or lower.
What Abnormal Results Mean
There are many kinds and degrees of hearing loss. In some types, you only lose the ability to hear high or low tones, or you lose only air or bone conduction. The inability to hear pure tones below 25 dB indicates some hearing loss.
The amount and type of hearing loss may give clues to the cause, and chances of recovering your hearing.
The following conditions may affect test results:
There is no risk.
There are many kinds of hearing function tests. In simple screenings, the health care provider will make a loud noise and watch to see if it startles you. Detailed screenings include brainstem auditory evoked response testing (BAER). This test uses an electroencephalogram to detect brain wave activity when sounds are made.
Another hearing test called otoacoustic emission testing (OAE) can be used in very young children (such as newborns).
Kileny PR, Zwolan TA. Diagnostic audiology. In: Cummings CW, Flint PW, Haughey BH, et al, eds. Otolaryngology: Head & Neck Surgery. 5th ed. Philadelphia, PA: Mosby Elsevier; 2010:chap 133.
Norton SJ, Bhama PK, Perkins JA. Early detection and diagnosis of infant hearing impairment. In: Cummings CW, Flint PW, Haughey BH, et al, eds. Otolaryngology: Head & Neck Surgery. 5th ed. Philadelphia, PA: Mosby Elsevier; 2010:chap 190.